Question 1

Is the wire all black no white writing on it? View answer

Asked 11 ´months ago | 18/2 SVT Black 105 Degree Two Conductor Service Wire

Question 2

Were are the sockets made? I assume they are not Leviton View answer

Asked 11 ´months ago | 2 Light 1/8ips. Top and 1/4ips. Bottom Threaded Pull Chain Wired Cluster - Antique Brass Finish

Question 3

does this slip over a 1/4 IPS (male) fully threaded pipe? otherwise, which one should i use? View answer

Asked 11 ´months ago | 5/8in. Smooth Unfinished Brass Tubing

Question 4

What size light bulb will fit in this globe? View answer

Asked 11 ´months ago | 4.5in. Opal White Glass Ball with 2-1/4in. Neck

Question 5

My pendant is about 8.5lbs. Cable length needed is 48"-50". How much weight can such cable support? View answer

Asked 11 ´months ago | 18/3 SVT Clear 105 Degree Three Conductor Pendant and Table Lamp Wire

Question 6

What is size of inner raised piece? View answer

Asked 11 ´months ago | 4in Fitter Flat Steel Shade Holder - Brushed/Satin Nickel Finish

Question 7

Hi - have a three socket Benjamin lamp; each with it's own pull chain and they attach from the side of the socket. View answer

Asked 11 ´months ago | Antique Brass Finish E-26 Standard Adjustable Cluster

Question 8

shipping timing View answer

Asked 11 ´months ago | 4-1/4in. Cross Bar with 8/32 Tapped Ground Hole

Question 9

where is the ul mark View answer

Asked 11 ´months ago | Polarized Plug Safety Label

Question 10

Will this fit on your medium-base bulb clips? View answer

Asked 12 ´months ago | 5/16-27 UNS - 5/8in X 1/2in Cylinder Finial - Unfinished Brass

Question 11

Hi, Can you get this in a bayonet View answer

Asked 12 ´months ago | Leviton - Brown Single Lampholder to Twin Lampholder Adaptor for E-26 Sockets

Question 12

will your 10" shade ring work with a harp that has a quarter28 stud? View answer

Asked 12 ´months ago | 10 inch Diameter #10 Steel Wire Shade Ring

Question 13

What is the OD of the check ring? View answer

Asked 12 ´months ago | 5/8in. x 1/8ips Threaded Straight Edge Turned Brass Check Ring

Question 14

What is the weight rating on this? View answer

Asked 12 ´months ago | 1-1/16in Hole Canopy Chain Hanging Cross Bar Set - Black Powdercoat Finish

Question 15

Hi. Could you tell the center to center distance between the three holes? Thanks! View answer

Asked 12 ´months ago | 5in 3-Hole Multiport Screw less face mount Canopy - Unfinished Brass

Question 16

what is the max weight this can hold View answer

Asked 12 ´months ago | E26 Porcelain Socket with Pendant Fixture with 18/3 SVT Cord - White Finish

Question 17

Does this have any UL rating View answer

Asked 12 ´months ago | 1/8ips Slip Through Plastic Wire Clamp Strain Relief - Black

Question 18

What is the manufacturere model number for this lampholder - needed for my ETL report description View answer

Asked 12 ´months ago | E26 Porcelain Twin Lamp Socket with 1/8ips Threaded Pre-Wired with 24in Leads

Question 19

Item # HO2-14CLPBL, will the clamp fit on a 1.5 inch diameter light socket? View answer

Asked 12 ´months ago | 2-1/4in. Clamp On Holder For Porcelain Socket With Lip - Black Powdercoated Finish

Question 20

Hello, How many feet are on a full spool? thanks View answer

Asked 12 ´months ago | 18/2 SPT-1 Burgundy/Wine Nylon Over Braid White 105 Degree Wire

Question 21

What size is the hole in the bottom? View answer

Asked 12 ´months ago | 3/4in. x 1/2in. Diamond Knurled Dimmer Knob With Set Screw - Polished Nickel

Question 22

How do I wire this into my lamp? View answer

Asked 12 ´months ago | 300 Watt Rotary Base Dimmer - For Incandescent/Halogen ONLY

Question 23

Is 2-1/2" width across the flared top edge or inside where sides are straight? I need inside dimension. View answer

Asked 12 ´months ago | 2-1/2in. Spun Brass Cup - Unfinished Brass

Question 24

hello, will this fit into NE952 or NE742? View answer

Asked 12 ´months ago | Flanges And Clamps - Pipe Mounting > 1/8ips (3/8in O.D) Male Threaded Brass Flange - Unfinished Brass

Question 25

Thread size View answer

Asked 12 ´months ago | Hang Straights - Ceiling Adapters > 1/8ips. Female Bottom X 1/4ips. Female Top 90 Degree Hang Straight - Unfinished Brass

Question 26

What is the dimension range of the hole size this will this clip into? View answer

Asked 12 ´months ago | 6ft. Black SPT-1 Cordset with E-12 Lamp Base Butterfly Socket, Cordswitch, and Molded Polarized Plug

Question 27

UL listed? The white variant looks like it is. View answer

Asked 12 ´months ago | 8ft. Black E26 Pendant Fixture for 1-3/8 in. Hole Shade

Question 28

Is this bulbl can be used in wet/damp places? View answer

Asked 12 ´months ago | 5W T6 120V 2-Pin G9 Base Clear Finish 2700K Specialty LED Miniature Light Bulb

Question 29

what is the then total height of this canopy (including the collar loop) View answer

Asked 12 ´months ago | 1-1/16in Center Hole - Tapered Spun Canopy Kit - Unfinished Brass

Question 30

What is the thickness of this felt with the sticky back material? View answer

Asked 12 ´months ago | Tools - Lamp Making Supplies > Felt Pads - Protective pads > 24in Wide X 36in Long Black Self Adhesive Sticky Back Felt

Question 31

Is this switch UL Recognized? View answer

Asked 12 ´months ago | On-Off Sub-Miniature Toggle Switch with 6in Long 18/1 Wire Leads

Question 32

Does this come in a clear glass? View answer

Asked 12 ´months ago | 12in. White Cone Shade with 2-1/4in. Neck

Question 33

Is this available in a brushed nickel finish? View answer

Asked 1 ´year ago | 1/2in Diameter - 8/32 UNC Threaded Brass Ball - Polished Nickel

Question 34

So I could probably put this under a socket, inside the neck/base of a 1.625" glass straight fitter? View answer

Asked 1 ´year ago | 120mm (4-3/4in) Diameter - Triple Leg Spring Clip Shade Holder with 1/8ips Slip Center Hole

Question 35

What is the thicknesses of the brass? Thank you View answer

Asked 1 ´year ago | 80mm. Open Ball Shade with 1/8ips Hole and 2-1/4in. Opening - Unfinished Brass

Question 36

I am looking for a brass sphere that is 9" or 9 1/2" in diameter. View answer

Asked 1 ´year ago | 200mm (7.87in) Diameter Cast Brass Hollow Ball Sphere - Unfinished Brass

Question 37

what is the weight limit for this item View answer

Asked 1 ´year ago | 1/4ips - Female Threaded - Snap Hook Quick Collar Loop - Black Finish

Question 38

will this work with nylon covered svt? what would be appropriate for that? View answer

Asked 1 ´year ago | 1/8ips. Male Threaded SVT Strain Relief - Unfinished Brass

Question 39

e26 or e27 base View answer

Asked 1 ´year ago | E-26 Keyless Socket with 1/8ips. Female Threaded Cap - Unfinished Copper

Question 40

Will this wire fit through a 1/8ips nip? Thanks :) View answer

Asked 1 ´year ago | 18/2 SVT-B Black/White Zig-Zag Pattern Nylon Fabric Cloth Covered Pendant And Table Lamp Wire

Question 41

Hi if I have a picture of some parts can you tell me which part it is View answer

Asked 1 ´year ago | 1/8ips Slip X 1/8ips Threaded - 5/8in Diameter Tee Fitting Ball Armback- Unfinished Brass

Question 42

Is this socket full range dimmable and what’s the diameter of the top? View answer

Asked 1 ´year ago | 200W Dimmable Phenolic Socket With 1/8ips Female Threaded Cap - Black

Question 43

How much does the shade weigh? View answer

Asked 1 ´year ago | 15in. Opal White Torchiere with 1-5/8in. Neck

Question 44

Is the hole at the wide end of the cone tapped? If so, what thread size? View answer

Asked 1 ´year ago | Brass Suspension System Cone Shaped Ceiling Gripper with Side Cable Exit and Locking Nut - Unfinished Brass

Question 45

How thick is the big and small link. View answer

Asked 1 ´year ago | Small Oval Shape Lamp Chain with Round Joining Links - Unfinished Brass

Question 46

What size are the set screws View answer

Asked 1 ´year ago | Nozzles - Female To Male Adapters > 1/8ips Male x 1/8ips Slip Female with Three Set Screws Nozzle - Unfinished Brass

Question 47

What is the larger hole diameter of GLGB05SFCL? The fitter hole is 1-3/16, but what is the other hole? View answer

Asked 1 ´year ago | 4-9/16in. Diameter Glass Open Ball with 1-3/16in. Hole - Clear

Question 48

Are these 16 threads per inch? I also need nuts to fit this. View answer

Asked 1 ´year ago | 24in. x 1/4ips. Threaded Zinc Plated Steel Hollow Nipple

Question 49

How much does this lamp base weigh? View answer

Asked 1 ´year ago | 11in Diameter Cast Brass Floor Lamp Base - Unfinished Brass

Question 50

How much does it weigh? View answer

Asked 1 ´year ago | 6-3/8in Cast Brass Figurine Base with 6in Seat and 1/8ips Threaded Hole - Unfinished Brass