Question 1

Is the socket for SO10085G the Leviton 10045? View answer

Asked 3 ´months ago | E-26 Porcelain Socket with 1/8ips. Cap and 10ft. Gold Wire Leads

Question 2

What is the length of the arm projection? View answer

Asked 3 ´months ago | One E-26 Light - Long Bent Arm - Wall Sconce for 1-5/8 Opening Shade - Unfinished Brass

Question 3

If I order two can I get combined shipping? View answer

Asked 3 ´months ago | DIY - Choose Your Color - Tea Cup Table Lamp Kit

Question 4

Male coupling / female gas cap thread size? View answer

Asked 3 ´months ago | 1/8ips Slip Telescopic Clutch with 1/4ips Female Thread - Unfinished Brass

Question 5

4 position foot control switch View answer

Asked 3 ´months ago | Step-On Foot Switch with Push In Terminals - White

Question 6

18/2 SVT-B or 16/3 SJT-B for 10amp Shark Navigator vacuum? View answer

Asked 3 ´months ago | 18/2 SVT-B Purple Nylon Fabric Cloth Covered Pendant and Table Lamp Wire

Question 7

Does this come in a taller size? View answer

Asked 3 ´months ago | Clear Glass Williamsburg Style Glass with 1-5/8in. Neck

Question 8

could you add the internal ID please ? or wall thickness ? thanks View answer

Asked 3 ´months ago | 5in Flat Canopy/Base without Wire Way - Unfinished Brass

Question 9

This should fit under my bronze lamp base as a counter weight. Will this work? View answer

Asked 3 ´months ago | 11in Diameter Round Marble Lamp Base - White

Question 10

What size shade would fit on this base? View answer

Asked 3 ´months ago | One Arm Solid Cast Brass Wall Sconce - Unfinished Brass

Question 11

What is the thickness of the check ring? View answer

Asked 3 ´months ago | 4-1/2in. X 1/8ips Threaded Straight Edge Turned Brass Check Ring

Question 12

Will this cord slide through 1/8”ips nipple? View answer

Asked 3 ´months ago | 8FT BLACK 18/2 NISPT-1 PVC Insulated Parallel Flexable Cord

Question 13

Is this unit dimable? View answer

Asked 3 ´months ago | 60w A/C, 12V LED Driver - 120V Input - 12 V Out

Question 14

What is the size of the screw holes for this holder? The ones that came with it are too long and need replacements View answer

Asked 3 ´months ago | 3-1/4in. Holder with 1/8ips. Hole - Brass Plated Finish

Question 15

Do you have this with longer wire? I need at least 24” View answer

Asked 3 ´months ago | 3-way Keyless Porcelain E-26 Socket with 1/8ips. Hickey And 6in. Wire Leads.

Question 16

Dose this come in polished brass? View answer

Asked 3 ´months ago | 1/2in. Diameter Ball - 1/8ips Threaded Brass Ball - Antique Brass Finish

Question 17

can I cut these down and do you have the possibility to order in brown for bronze lights View answer

Asked 3 ´months ago | 4in Long Black Paper/Kraft E-12 Candle Socket Cover

Question 18

Does this sit on milk glass interior shade of metal tole lampshade View answer

Asked 3 ´months ago | 12 inch Diameter #10 Steel Wire Shade Ring

Question 19

Hi. For this product, is the inner diameter the 1/8ips? View answer

Asked 3 ´months ago | 1-1/2in Long X 5/8in Diameter - 1/8ips Threaded Unfinished Brass Coupling.

Question 20

Are these glass or acrylic? View answer

Asked 3 ´months ago | 50mm (2in.) Crystal Pear Drop with Jewel and Nickel Plated Clip

Question 21

I'm looking for a student vintage milk Glass Shade with fluted top with a 5-3/4 inch fitter. One of the two I have View answer

Asked 3 ´months ago | Opal Student Shade with Ruffle Top and 8in. Neck

Question 22

Can you offer this with a shorter pipe? 1 inch or 2 inch? View answer

Asked 3 ´months ago | Wall Sconce with Keyless UNO Threaded Lamp Socket - Unfinished Brass

Question 23

This is 16” long end to end? When screwed into fittings it is then 15.63” long then correct? View answer

Asked 3 ´months ago | 16in Long - 1/8ips (3/8in OD) Steel Pipe with 3/16in long thread on both ends - Satin Nickel

Question 24

Is this UL listed View answer

Asked 3 ´months ago | One Light Wall Sconce Kit Unfinished Brass - You Assemble Yourself and Save!

Question 25

If I wanted to use this as a cabinet knob, what sort of screw or bolt would suit the threading inside the knob/dial View answer

Asked 3 ´months ago | 11/16in H x 3/4in W Knurled Dimmer Knob Unfinished Brass With Set Screw

Question 26

What is the height of just the collar / fitter? (Diameter is 2 9/16 but what's it's height off bowl?) View answer

Asked 3 ´months ago | 10in. Top Hand Blown IES Opal Glass Shade with 2-5/8in. Neck - USA

Question 27

Looking for an adapter 1/4-20 female with one end 1/4-27 for the finial. View answer

Asked 3 ´months ago | 1/4-27 UNF Female X 1/4ips Male Threaded Slotted Reducer without Shoulder

Question 28

IS THIS SOLID BRASS? View answer

Asked 3 ´months ago | 4in. Fitter Antique Brass Semi-Flush Lighting Fixture.

Question 29

Does this allow an armback (AB472SN) and a straight coupling (NE470SN) to be connected and flush with each other? View answer

Asked 3 ´months ago | 7/16in Long 1/8ips. Unfinished Brass Nipple with Shoulder

Question 30

what is the load limit? View answer

Asked 3 ´months ago | Brass Suspension System Snap Hook Gripper for use with 1-1.5mm Steel Cable - Unfinished Brass

Question 31

which side is down? View answer

Asked 3 ´months ago | Weights - Loaders > 9-3/4in. 8 lb Cast Iron Floor Lamp Weight with Feet and 1/4ips. Threaded Center Hole

Question 32

Is there a listing to buy an extra ring for this cup? Or perhaps another compatible ring listing? View answer

Asked 3 ´months ago | Edison brass threaded cup with 2in Diameter Ring and 1/8ips slip through hole - Antique Brass

Question 33

Is there a listing to buy just the shade ring? View answer

Asked 3 ´months ago | Threaded Skirt Socket Cup With Shoulder and Knurled Shade Ring - Antique Brass Finish

Question 34

What is the difference between this one and SKU:CY872138COLOR/ FINISH:ClearTYPE:Crystal - Pear DropLENGTH:1.500 (1- View answer

Asked 3 ´months ago | 38mm. (1-1/2in) long x 1in W Strass Crystal Pear Drop.

Question 35

what size are the screws? View answer

Asked 3 ´months ago | 3-1/4in. Screw In Brass Holder With Porcelain Two Piece E-26 Screw-in Adaptor

Question 36

Do you have solid brass rods 4" long with 1/2" male and female threads on each end? View answer

Asked 3 ´months ago | 4 in. Long - 8/32 Threaded Brass Rod with 1/2in Long Thread on Both Ends.

Question 37

what is the diameter of the wire View answer

Asked 3 ´months ago | #20 Nickel Plated Tie Wire

Question 38

what size is the screw that the knob fits on? I've got an old fixture, screw needs to be 4mm or smaller (metric!) View answer

Asked 3 ´months ago | 3/8in Shank On/Off Rotary Lamp Switch with Removeable Knob and Wire Leads - Brass Plated

Question 39

Will this item thread into loop sku #LO316 View answer

Asked 3 ´months ago | 1/2in. Long thread X 1/8ips. Male Threaded Steel Hex Head Nipple

Question 40

What is the IP rating for this socket? View answer

Asked 3 ´months ago | Grounded 1-5/8in Height Porcelain E-12 Base Damp Location Rated Lamp Socket with 72in Wire Leads.

Question 41

how to you open the terminal cover ? I got the box screw out but the cover does not open View answer

Asked 3 ´months ago | Rondo In-Line Sliding Dimmer with Push Switch and Slider - Black

Question 42

what is the thickness of cross bar CB18HD ? View answer

Asked 3 ´months ago | 1/8ips Heavy Duty 14 Gauge Zinc Plated Crossbar

Question 43

Is this kit UL Approved? https://grandbrass.com/choose-your-finish-choose-your-length-downrod-pendant-kit/ View answer

Asked 3 ´months ago | Choose your Finish / Choose your Length Downrod Pendant Kit

Question 44

Can you sell these in the UK? View answer

Asked 3 ´months ago | 18in. Opal Flying Saucer Pointed Glass Shade with 6in. Neck

Question 45

WHAT IS THE THREAD SIZE (NOT 1/8" IPS AS NOTED IN COMMENTS) View answer

Asked 3 ´months ago | 300W Max - 120V Rotary Dimmer Switch with Plastic Housing and 1in long shank

Question 46

I'm looking for solid wire View answer

Asked 3 ´months ago | 18/1 SF1 White Single Conductor High Heat 200 Degree Wire

Question 47

can this be made in unfinished brass? View answer

Asked 3 ´months ago | Double 2-1/4 Shade Holder Wall Sconce - Polished Nickel Finish

Question 48

is this wire ok for pull down pulley adjustable fixture View answer

Asked 3 ´months ago | 18/2 SVT Black 105 Degree Two Conductor Service Wire

Question 49

Is this suitable for dimmable LED lamps? View answer

Asked 3 ´months ago | In-line Sliding Foot Dimmer with 6ft. Wire Lead - Black

Question 50

So I'm unfamilar with the jargon. When you say 2 3/4 fitter i assume that is the hole size not the height of the View answer

Asked 3 ´months ago | 14-1/2in. Frosted Swirl Torchiere with 2-3/4in. Neck

Tools